Hondata S300 Kit Version3
The Hondata s300 is a plug in module to the factory Honda Engine Computer (ECU) which vastly expands the capabilities of the factory ECU. Forced induction, datalogging, real time updating of parameters, engine protection are but a few of the s300 features.
Main features: Fits inside the ECU Built on the proven s100/s200 code base USB connection for speed and compatibility SManager Windows based software for parameter & table editing, calibration uploading and datalogging. Real-time updating of ECU Built in calibrations for common engine combinations Built in datalogging to a laptop On board datalogging memory (2 MB memory, 20-60 minutes datalogging) Adjustment for different sized injectors, with overall fuel trim. Configurable for any MAP sensor (to at 5 Bar and above) TPS based table lookup for ITBs Engine protection from over boost and over temperature. Expanded fuel and ignition tables, both in rpm and load, to 60 lbs boost and 11,000 rpm (these are not the upper limits) Launch control with anti-lag Full throttle shift Two multi purpose outputs for nitrous control or similar Lambda tracing (with a wideband o2 sensor)
SManager editing software features: High and low speed 24 x 20 ignition and fuel tables for correct VTEC tuning Injector size fuel trim Fuel trim for starting, throttle tip in and individual cylinder trim Rev limiter with fuel cut or fuel and ignition cut Launch control with anti-lag Full throttle shift Adjustable VTEC window with load and throttle control Secondary intake runner control Adjustable idle speed MAP sensor type and calibration Adjustable boost cut with hot and cold settings Shift light Closed loop control Air temperature compensation Water temperature compensation Fuel and ignition correction based on gear A/C shutoff conditions Closed loop Two general purpose outputs for nitrous control, BOOST CONTROL (SEE RELATED PRODCUTS) or similar
On board datalogging trigger conditions The s300 uses different connecting pins in the ECU from the s100/s200, and also has a slot cut in the side for the USB connector, so the ECU must be modified for use with the s300.
This s300 is made to fit in a full frame OBD1 ECU case (US and most markets) not JDM
Main features: Fits inside the ECU Built on the proven s100/s200 code base USB connection for speed and compatibility SManager Windows based software for parameter & table editing, calibration uploading and datalogging. Real-time updating of ECU Built in calibrations for common engine combinations Built in datalogging to a laptop On board datalogging memory (2 MB memory, 20-60 minutes datalogging) Adjustment for different sized injectors, with overall fuel trim. Configurable for any MAP sensor (to at 5 Bar and above) TPS based table lookup for ITBs Engine protection from over boost and over temperature. Expanded fuel and ignition tables, both in rpm and load, to 60 lbs boost and 11,000 rpm (these are not the upper limits) Launch control with anti-lag Full throttle shift Two multi purpose outputs for nitrous control or similar Lambda tracing (with a wideband o2 sensor)
SManager editing software features: High and low speed 24 x 20 ignition and fuel tables for correct VTEC tuning Injector size fuel trim Fuel trim for starting, throttle tip in and individual cylinder trim Rev limiter with fuel cut or fuel and ignition cut Launch control with anti-lag Full throttle shift Adjustable VTEC window with load and throttle control Secondary intake runner control Adjustable idle speed MAP sensor type and calibration Adjustable boost cut with hot and cold settings Shift light Closed loop control Air temperature compensation Water temperature compensation Fuel and ignition correction based on gear A/C shutoff conditions Closed loop Two general purpose outputs for nitrous control, BOOST CONTROL (SEE RELATED PRODCUTS) or similar
On board datalogging trigger conditions The s300 uses different connecting pins in the ECU from the s100/s200, and also has a slot cut in the side for the USB connector, so the ECU must be modified for use with the s300.
This s300 is made to fit in a full frame OBD1 ECU case (US and most markets) not JDM
